Lingenfelter Performance Engineering1557 Winchester RoadDecatur, IN 46733(260) 724-2552 (260) 724-8761 faxwww.lingenfelter.comRevision - 1.9Release da
Page 9. 25. Disconnect the brake booster hose from the top of the supercharger front cover.26. Disconnect the purge solenoid electrical connector fr
Page32. Using a 10 mm socket, remove the two bolts on the bypass actuator bracket. NOTE: Do not remove the actuator at this time.10. 29. Disconne
Page11. 35. Using an 10 mm socket, start with the back six (6) bolts and remove the sixteen (16) bolts from the supercharger cover. Refer to the bolt
Page38. Cover the supercharger inlet with rags or plastic to prevent debris from entering the supercharger.12. 39. Using a 10 mm socket, remove the
Page13. 41. Carefully lift up on the front of the supercharger and place a wooden block or equivalent underneath to wedge the front of the supercharg
Page43. Using a pry bar, carefully pry the front cover in the location shown. Make certain any wires or lines are not in the way. This step may req
Page15. 50. Notice the pulley is clamped evenly, the end is ush with the bearing rod, and the hole is drilled in the center of the end of the pulley
Page16. 52. Secure the front cover and supercharger pulley. Using a hammer and punch, hit the two surfaces around the pin shown to the left. This w
Page17. 56. Apply a thin lm of the supplied Permatex Ultra Black Gasket maker to the mounting surface of the front cover.57. Insert the LPE provide
Page59. To the left shows an LPE ported supercharger front cover. The porting is provided as part of the LPE pulley installation and ECM calibration
Page 1. Parts List # Part number Description 1 8PK1655 8 rib 1655mm belt 1 ETN307091 Pulley Cap 1 82180 Permatex Ultra Black Gasket Maker,
Page 19. 63. (Left side of factory airbox)64. (Under side of factory airbox)65. (Right side of factory airbox)66. (Right side of factory airbox)
Page67. Cut the airbox along your marked lines. After the nal cuts have been made, your new airbox should look like this.68. Re-install your air
Page 21. 71. Using a breaker bar, release the tension on the tensioner by turning it counter-clockwise. While the tension is released install the LP
Page22. 74. Insert the bypass actuator arm into the supercharger front cover bracket. Replace the PCV hose and correct vacuum hose as shown.75. Use
Page 23. 79. Install the boost solenoid bracket onto the bypass valve actuator. Torque the bolt down to 89 lb-in (10Nm). 80. Reconnect the vacuum
Page24. 82. Replace the inlet air pressure electrical connector.83. Install the purge solenoid onto the front cover. Using a 10 mm socket, torque th
Page25. 87. Replace the electrical connector to the IAT2 sensor.88. Replace the electrical connector to the BARO sensor.89. Re-connect the brake bo
Page91. Replace the throttle actuator electrical connector to the throttle body.92. Install the barbed end of the supplied 45 degree plastic tting
Page96. Loosen both band clamps and put them on both couplers. Gently work the LPE provided elbow into both couplers. Move each band clamp towards
Page98. You can purchase vehicle programming hardware and software from LPE, you can send in your ECM for us to calibrate or you can have a local tun
PageThe Lingenfelter CTS-V Supercharger Pulley Upgrade Kit is designed to increase the speed of the LSA Eaton TVS1900 supercharger in order to deliver
Page 29. Table 1 - belt length and idler pulley diameters required for different LSA supercharger pulley and damper pulley combinations.Crank PulleyPN
PageLingenfelter Performance Engineering1557 Winchester RoadDecatur, IN 46733(260) 724-2552 (260) 724-8761 faxwww.lingenfelter.comL250070709 Lingenfel
Page3. 1. Open the hood of the vehicle. If you have been driving the vehicle, allow the vehicle to cool down for a few hours before beginning this wo
Page 4. 5. With the strut tower brace removed, remove the back plastic cover by pulling up from either side of the intercooler.6. Remove the connect
Page5. 11. Using a T-25 Torx tool, remove the three (3) Torx bolts from the top portion of the air lter housing. The location of the rst bolt is
Page13. The location of the third bolt is directly behind the driver front headlight assembly.6. 14. Carefully remove the top of the air lter housi
Page 7. 18. Using a 1/2” breaker bar, release the tension in the supercharger belt tensioner located on the passenger side by turning the tensioner c
Page8. 21. Carefully remove the throttle body. Do not allow dirt or debris to enter the throttle body or front cover during the installation.22. Re
Comments to this Manuals